Skip to main content Skip to content

Beatbot

Beatbot Sora 30 vs. Sora 70: A Detailed Analysis

7 min read
Beatbot Sora 70 robotic pool cleaner beside a backyard pool

The Beatbot Sora 30 and Sora 70 are cordless robotic pool cleaners built on the same 6,800 GPH, 10,000 mAh platform, and the difference between them comes down to one zone: the water surface. This comparison lines up the specifications from both listings, explains what the Sora 70's surface cleaning adds, and covers filtration, runtime, setup, retrieval, and warranty so you can match the right model to your pool.

Key takeaways

  • Both clean the floor, walls, waterline, and shallow platforms down to 8 inches with 6,800 GPH of suction and SonicSense dual ultrasonic navigation.
  • Only the Sora 70 cleans the water surface, using JetPulse dual converging jets, and it adds remote surface navigation in the Beatbot app.
  • The Sora 70 has a 6 L basket that holds up to about 800 leaves and five cleaning modes; the Sora 30 has a 5 L basket and three modes.
  • Both run on a 10,000 mAh battery: up to 5 hours on the Sora 30; up to 7 hours surface, 5 hours floor, or 4.5 hours full clean on the Sora 70.
  • The Sora 30 carries a 2-year limited warranty and the Sora 70 a 3-year limited warranty.

What is the main difference between the Sora 30 and Sora 70?

Surface cleaning is the dividing line. The Sora 70 is the only cleaner in the Sora series that cleans the water surface as well as everything below it, covering five zones in one machine: surface, floor, walls, waterline, and shallow platforms. The Sora 30 covers the four below-water zones and leaves the surface alone, which keeps its price below the Sora 70 while still covering the areas where most debris settles.

Waterline cleaning and surface cleaning are different jobs. Both robots scrub the band where the wall meets the water, but only the Sora 70 travels across the surface to pull in floating leaves, pollen, and bugs. If a skimmer or a covered pool already handles floating debris, the Sora 30 covers the work that remains; if surface debris is a daily chore, the Sora 70 handles it in the same machine.

Beatbot Sora 30 shown cleaning the pool floor, walls, waterline, and shallow platforms
The Sora 30 cleans the floor, walls, waterline, and shallow platforms; it does not clean the water surface.

Sora 30 vs. Sora 70 specifications

Specification Beatbot Sora 30 Beatbot Sora 70
Cleaning zones Floor, walls, waterline, shallow platforms Water surface, floor, walls, waterline, shallow platforms
Shallow-water cleaning Down to 8 in Down to 8 in
Surface cleaning Not included JetPulse dual converging jets
Suction 6,800 GPH (25,700 LPH) 6,800 GPH, 6.7 in intake
Navigation SonicSense dual ultrasonic sensors with AI, S-shaped path SonicSense dual ultrasonic sensors with AI, S-shaped path
Cleaning modes 3 5
Debris basket 5 L 6 L, up to about 800 leaves
Filter 150 micron, optional 3 micron 150 micron, optional 3 micron
Battery 10,000 mAh 10,000 mAh
Runtime Up to 5 hr per charge Up to 7 hr surface, 5 hr floor, 4.5 hr full clean
Maximum coverage Up to about 3,200 sq ft Up to 3,230 sq ft
Retrieval Floating chambers surface it and guide it to the edge Buoyancy chambers float it to the edge
App control Wi-Fi (2.4 and 5 GHz) or Bluetooth; can start without a connection Beatbot app with remote surface navigation
Saltwater Up to 5,000 ppm Up to 5,000 ppm
Warranty 2-year limited 3-year limited

Coverage is effectively a tie at about 3,200 square feet for the Sora 30 and 3,230 for the Sora 70. Suction, battery capacity, navigation, and shallow-water reach match as well, so the decision rests on surface cleaning, basket size, mode count, and warranty length. Beatbot does not publish exact dimensions or charging time for either model, so those figures are left out here rather than estimated.

What does the Sora 70's surface cleaning add?

The Sora 70's JetPulse system uses dual converging jets to pull floating debris inward and capture it on the first pass, rather than pushing leaves and pollen away the way passive skimmers do. Remote water-surface navigation in the Beatbot app lets you steer it by hand for spot cleaning. The listing positions this as removing the need for a separate skimmer and a second cleaning step.

Surface work also gets the longest runtime on either listing, up to 7 hours, while a full five-zone clean runs up to 4.5 hours. That makes the Sora 70 the stronger fit for pools near trees or in windy areas, where leaves, pollen, and bugs land on the surface and turn into a separate chore. You can read more about the model in our Sora 70 feature guide.

Adding surface coverage to a Sora 30

Owners who prefer the Sora 30 for the floor can cover the surface with a second robot. RoboticsSelect carries a Sora 30 bundle with Beatbot's solar-powered robotic pool skimmer, which works the surface throughout the day while the Sora 30 runs floor-cleaning cycles as needed. Both robots run from the same Beatbot app.

How do they compare below the water?

Below the surface, the two are closely matched. Both deliver 6,800 GPH, with the Sora 70 drawing through a 6.7-inch intake, and both use SonicSense dual ultrasonic sensors with AI to plan an S-shaped path and steer around obstacles. Both clean shallow platforms down to 8 inches, which reaches tanning ledges, swim-outs, and sun shelves. The Sora 30 listing adds front and rear dual roller brushes for wider coverage, tighter turns, and stronger traction when climbing walls.

Filtration and basket size

Each robot ships with a 150-micron basket installed, and each accepts an optional 3-micron ultra-fine filter for very fine particles. The Sora 70's 6-liter basket holds up to about 800 leaves, against 5 liters on the Sora 30, so the Sora 70 can go longer between empties in a leafy pool.

Runtime and cleaning modes

Both carry a 10,000 mAh battery. The listing states the Sora 30 runs up to 5 hours per charge, enough to finish most pools in one session regardless of debris load. The Sora 70 runs up to 7 hours on the surface, up to 5 hours on the floor, or up to 4.5 hours for a full five-zone clean; these are separate mode figures, not a running total. Its five modes cover quick touch-ups, surface-only runs, and deep full-pool cleans, while the Sora 30 has three modes.

Setup, control, and retrieval

Setup is the same short sequence for both: charge fully before the first run, install the Beatbot app and pair the robot, choose a mode, then lower it into the water and start the cycle. Set the mode before the robot submerges, because the Sora 30's wireless link drops underwater and the Sora 70's app navigation works only while it is on the surface. The Sora 30 can also be started directly without a connection.

Retrieval works slightly differently on each. When a Sora 30 cycle ends or its battery drops below 12 percent, floating chambers lift it to the surface and guide it to the pool edge. The Sora 70 uses buoyancy chambers to float to the edge when it finishes. Either way, you lift the robot out, rinse the basket, and recharge it with the included charger; our Sora 30 maintenance guide covers the routine in more detail.

Before you buy

Decide where your debris lands. If most of it sinks, or a skimmer already handles the surface, the Sora 30 covers the floor, walls, waterline, and shallow platforms. If leaves and pollen sit on the surface every day, choose the Sora 70 or the Sora 30 skimmer bundle. Measure any tanning ledge or swim-out against the 8-inch shallow-water rating, and check your salt level against the 5,000 ppm limit.

Beatbot Sora 70 JetPulse jets collecting floating leaves on the water surface
The Sora 70 is the only Sora model that also cleans the water surface.

Warranty, shipping, and support

Warranty length is the clearest ownership difference. The Sora 30 carries Beatbot's 2-year limited manufacturer warranty and the Sora 70 a 3-year limited warranty, both for defects in materials and workmanship under normal residential use from the date of delivery. For a covered issue, Beatbot's technical team evaluates the unit and either repairs it or provides a new or refurbished replacement. Normal wear on filters, brushes, and tracks is not covered, and neither is damage from water chemistry outside the recommended range.

RoboticsSelect is an authorized Beatbot dealer, so warranty requests go through our support team, which coordinates with Beatbot. Shipping is free to the contiguous 48 U.S. states; we do not ship to PO boxes, Alaska, Hawaii, Puerto Rico, or outside the U.S. (see the shipping policy). Unopened, unused units can be returned within 30 days under the refund policy, and support runs through our U.S.-based, product-trained team at support@roboticsselect.com or (412) 415-7375.

The takeaway

The Sora 30 and Sora 70 share the same underwater hardware, so the choice comes down to the surface. Pick the Sora 30 when floating debris is already handled, and pick the Sora 70 when you want one robot for all five zones, a 6 L basket, and a 3-year warranty. Both are in the Beatbot collection at RoboticsSelect, and the Beatbot comparison page lines them up against the AquaSense models.

Products in this article

FAQ

Does the Beatbot Sora 30 clean the water surface?

The Sora 30 cleans the floor, walls, waterline, and shallow platforms down to 8 inches, but not the water surface. For surface cleaning, choose the Sora 70 or the Sora 30 and skimmer bundle.

Is the Sora 70 stronger underwater than the Sora 30?

Both are rated at 6,800 GPH with a 10,000 mAh battery and SonicSense dual ultrasonic navigation. The Sora 70's advantages are surface cleaning, a 6 L basket, five cleaning modes, and a 3-year warranty.

How long do the Sora 30 and Sora 70 run per charge?

The Sora 30 runs up to 5 hours. The Sora 70 runs up to 7 hours on the surface, up to 5 hours on the floor, or up to 4.5 hours for a full five-zone clean.

Can either model clean a tanning ledge?

Yes. Both clean shallow platforms down to 8 inches of water, such as tanning ledges and swim-outs. Measure the water depth on your ledge first.

Are the Sora 30 and Sora 70 safe for saltwater pools?

Yes. Both are rated for saltwater pools with salt up to 5,000 ppm and suit in-ground and above-ground pools with concrete, vinyl, fiberglass, or ceramic tile surfaces.

What warranty does each model carry?

The Sora 30 has Beatbot's 2-year limited warranty and the Sora 70 a 3-year limited warranty. RoboticsSelect is an authorized Beatbot dealer, so warranty support is handled through our support team.