WYBOT C1 Cordless Robotic Pool Cleaner | 2026 Upgrade

The C1 cleans the pool floor, walls, waterline, steps, and slopes, pulling leaves, sand, and dirt into a 180 micron filter cartridge with 3,038 GPH of suction. WYBOT notes the robot is built for debris cleaning, not water quality management or ultra-fine filtration, so it works alongside your pool's circulation and chemical treatment rather than replacing them. Very dirty water with a lot of suspended particles can reduce its cleaning efficiency.

No. When the cycle ends or the battery runs low, the C1 parks itself near the pool wall so you can lift it out; it cannot leave the water on its own. On the wall it holds itself in place by driving a jet of water outward, which presses the robot against the surface while it scrubs up to the waterline.

WYBOT rates the C1 for above-ground and in-ground pools of all shapes, on tile, concrete, vinyl, and fiberglass. For tiled or slippery surfaces, WYBOT recommends fitting the float block accessory that comes with the robot so it keeps its grip on the wall.

WYBOT rates the C1 for pools up to 1,615 square feet (about 150 square meters), which covers most backyard pools. Runtime, pool shape, and debris load all affect how much it finishes in one cycle. For larger pools, the C2 is rated to 2,152 square feet and the S2 to 3,230 square feet.

Up to 150 minutes in Eco Floor mode; modes that add wall and waterline passes draw more power and finish sooner. When the battery gets low the robot stops and parks by the wall for retrieval. A full recharge takes about 3 hours.

The WYBOT app (iOS 17.0 or later, Android 8.0 or later) is where you choose among the five modes (Full, Floor, Wall, Wall then Floor, Eco Floor), pick the S or N path, schedule up to four cleanings a week, and install over-the-air updates. Do the setup on the pool deck: WYBOT states the Wi-Fi and Bluetooth signal disappears once a cordless robot is underwater, so select the mode, close the app, and then place the robot in the pool.

WYBOT's guidance is to take it out after each cycle, rinse the filter cartridge, brushes, and other removable parts with fresh water, and store it in a ventilated spot out of direct sunlight; a deeper clean every few months is also recommended. WYBOT says a robotic cleaner can last up to five years when it is cleaned after every session. Running it once or twice a week is WYBOT's general guideline.

Balanced water. WYBOT's FAQ says its robots work in saltwater pools as long as salinity stays at or below 4,000 ppm, and it recommends rinsing the robot with fresh water after every cycle because salt accelerates wear on moving parts. WYBOT's warranty excludes damage caused by chemical imbalance in the pool water, so correct the chemistry before you run the cleaner rather than using it to help clear a pool that is out of range.

WYBOT covers the C1 with a 24-month limited warranty against defects in materials and workmanship, including the motor and pump, internal electronics, charging system, and battery. Brushes, wheels, filters, and rollers are wear parts and are not covered, and neither is damage from unbalanced pool water, water entering an unsealed cover or charging port, or unauthorized repair. WYBOT's policy does not ask for product registration; your RoboticsSelect order confirmation is your proof of purchase. RoboticsSelect is an authorized WYBOT dealer and handles claims: email support@roboticsselect.com or call (412) 415-7375, Monday through Friday 9am to 5pm EST, with your order number, the serial number, and a short description, photo, or video of the fault.

A full charge takes about 3 hours with the included adapter. If the charger will not start, WYBOT's first checks are that the robot is powered off before you plug in and that the charging port is completely dry, since moisture in the port causes charging failures and corrosion. Charge indoors, away from direct sun and heat; WYBOT advises against charging outdoors, even on a covered deck, because of the battery fire risk from sun exposure.

Set up your pool in the app before you pick a cleaning mode. WYBOT explains that the cleaning path changes with pool shape and surface material, so the app needs your pool defined first, and the right mode selected, to cover the whole pool. If it still misses areas, reselect a suitable mode in the app and rinse the filter after every cycle, as WYBOT recommends, so a full basket is not holding it back.

Rinse the filter and removable parts, dry the robot, and store it in a ventilated place out of direct sunlight and bad weather. WYBOT's support FAQ says to charge the cleaner every three months while it is not in use to maintain the battery, so put it away charged and top it up through the off-season.