Deep Robotics
Getting Started with Lynx M20 Pro
The Deep Robotics Lynx M20 Pro is a mid-sized, industrial-grade wheel-legged quadruped built for power inspection, emergency response, logistics, and field research. It rolls on wheels where the ground is flat and steps over obstacles where it is not, with dual LiDAR units and cameras driving SLAM mapping and autonomous navigation. This guide covers what the listing says the platform can do, how to prepare a first run, and what to confirm before purchase.
Key takeaways
- 33 kg with battery, a 15 kg rated payload (50 kg maximum static load), and operation in spaces as narrow as 50 cm.
- Up to 3 hours and 15 km unloaded, or 2.5 hours and 12 km at rated load, with hot-swappable batteries that charge in about 1.5 hours.
- Climbs continuous 25 cm stairs, clears single steps up to 80 cm, handles 45 degree slopes, and is rated at 5 m/s in lab testing with 2 m/s recommended in operation.
- IP66-rated, operates from -20 to 55 degrees C, and carries a 12-month full-unit warranty with 6 months on the battery and joints.
What is the Lynx M20 Pro?
Deep Robotics describes the Lynx M20 Pro as the world's first wheeled-legged robot built specifically for challenging terrain and hazardous environments in industrial operation. The wheel-leg design combines the rolling speed of wheels with the obstacle-crossing ability of legs, and the robot transitions between the two without manual reconfiguration, using Model Predictive Control and Reinforcement Learning for the wheel-to-leg transitions. That lets it cover ground efficiently while still handling stairs, slopes, debris, wetlands, and tunnels.
At 33 kg it is transportable by a single operator, and its 820 x 430 x 570 mm standing footprint lets it work in spaces as narrow as 50 cm. Deep Robotics positions it as a professional platform for trained operators and integrators rather than consumer use, which shapes everything that follows: plan the mission first, then confirm the robot fits it. For the broader category, see the quadruped robot buying guide.
Specifications that matter for deployment
| Specification | Listed figure |
|---|---|
| Standing dimensions | 820 x 430 x 570 mm |
| Weight | 33 kg (including battery) |
| Rated payload | 15 kg; 50 kg maximum static load |
| Endurance, unloaded | Up to 3 hours; 15 km range |
| Endurance, at rated load | 2.5 hours; 12 km range |
| Speed | 5 m/s lab-tested maximum; 2 m/s recommended operating speed |
| Stairs and steps | 25 cm continuous stair height; 80 cm maximum single step |
| Maximum slope | 45 degrees |
| Perception | Dual 96-line LiDAR units (360 x 90 degree field of view, about 860,000 points per second); dual wide-angle cameras with bidirectional lighting |
| Computing | Dual octa-core 64-bit industrial processors, each with 16 GB RAM and 128 GB storage |
| Ingress protection | IP66 |
| Operating temperature | -20 C to +55 C |
| Expansion power | 24 V / 72 V, up to 300 W for external devices |
Treat these as stated capabilities, not a promise that every maximum can be reached at once on your site. The 5 m/s figure is lab-tested; Deep Robotics lists 2 m/s as the recommended operating speed, so plan routes around the lower number. Use the table to build a site-specific acceptance sheet: record doorway widths, turning areas, route distances, slopes, and inspection stopping points, and where a requirement approaches a published limit, ask for a demonstration before committing to that route.

Perception, autonomy, and expansion
Autonomy is built on dual 96-line LiDAR units and dual wide-angle cameras, which together give a 360 by 90 degree field of view and roughly 860,000 points per second for SLAM, autonomous navigation, terrain recognition, and omnidirectional obstacle avoidance. Bidirectional lighting supports operation in darkness. Adaptive gait control with hyper-flexible joints and posture transitions handles irregular ground, and over-the-air updates keep the software current.
The platform is open. Gigabit Ethernet, USB 3.0, and RF image transmission provide connectivity, and the 24 V / 72 V expansion output supplies up to 300 W to third-party sensors, payloads, or compute modules. Integrators can add LiDAR, cameras, a robotic arm, or application-specific payloads through the mounting interfaces. It is the field-ready counterpart to the research-oriented Lite3 quadrupeds in the same collection.
How do you prepare for the first run?
The listing's getting-started sequence is the right order of operations. Unbox the robot and accessories and inspect for shipping damage before powering on. Insert a charged hot-swappable battery, or charge one fully, which takes about 1.5 hours. Power on and connect over Gigabit Ethernet or the supported wireless link, following the user manual. Apply any available OTA update before field operation. Run the startup checks, confirm LiDAR and camera perception, and test movement in a safe, open area before deploying on terrain. Confirm that operators are trained and follow Deep Robotics' operating limits for speed, slope, and load.
Build the first session around a checklist
Confirm the order contents against the quotation, since the listing notes that battery and controller quantities depend on configuration. Assign an operator, a test observer, and a person authorized to approve progression to the next stage. Prepare a controlled test area with a boundary and keep unrelated activity outside it. Record the baseline: configuration, installed payload, software version, battery condition, and test objective. Then run a limited trial that starts with straightforward movement and observation checks before adding route complexity. A documented, repeatable basic run is worth more than an ambitious demonstration that leaves the team unsure which conditions produced the result.
Applications to evaluate against your mission
Power inspection
Deep Robotics lists substations, transmission corridors, and electrical infrastructure as the core use, with the robot navigating autonomously to reduce human exposure in high-voltage environments while collecting consistent inspection data. For a pilot, choose one observation the team already understands, define the required viewing position and image quality, and make usable data, not a completed route, the acceptance criterion.
Emergency response and logistics
The wheel-leg design reaches rubble, steep slopes, and narrow access points that conventional wheeled platforms cannot, and the 15 kg rated payload serves logistics tasks across uneven sites. Begin with a controlled training scenario, write down the information responders need and the conditions that would end the mission, and include a recovery procedure in the plan.
Research and development
The open architecture supports work in quadruped locomotion, SLAM, autonomous navigation, embedded AI, and sensor fusion. Make the first milestone concrete: one interface, one experiment, one reproducible result. Developer resources are published on Deep Robotics' GitHub.

Before you buy
Write the mission before you write the purchase order: where the robot must travel, what it must collect, and who will act on the data. Confirm the exact configuration, including the number of batteries and whether a remote controller is included, since both depend on configuration. If a payload is part of the plan, keep it within the 15 kg rated load and the 300 W expansion budget, and send drawings for review before delivery rather than after.
Warranty, shipping, and support
The Lynx M20 Pro carries a 12-month full-unit warranty from the date of delivery, with the battery and joints covered for 6 months. Damage from misuse, negligence, or unauthorized modification, normal wear on consumable components, use outside recommended operating conditions, and unauthorized repairs or disassembly are not covered, and claims require valid proof of purchase. The box includes the robot, a hot-swappable battery pack (quantity per configuration), a battery charger and power cable, a remote controller for manual operation (per configuration), and the user manual and quick-start guide.
RoboticsSelect is an authorized Deep Robotics dealer, so warranty and repair requests go through our support team, which coordinates with Deep Robotics. Shipping is free to the contiguous 48 U.S. states; we do not ship to PO boxes, Alaska, Hawaii, Puerto Rico, or outside the U.S. Unopened, unused units may be returned within 30 days under the refund policy. Our U.S.-based, product-trained team is available at support@roboticsselect.com or (412) 415-7375.
The takeaway
The Lynx M20 Pro is a platform for organizations with a defined field mission: a route that mixes flat ground with stairs, slopes, and narrow passages, a payload under 15 kg, and operators trained to run it. Start with one measurable task, document the first runs, and expand from evidence. Full specifications and live pricing are on the Deep Robotics Lynx M20 Pro listing, and the Deep Robotics comparison page sets it beside the Lite3 line.
Products in this article
FAQ
How much can the Lynx M20 Pro carry?
The rated payload is 15 kg, with a maximum static load capacity of 50 kg. At rated load it runs 2.5 hours with a 12 km range.
How fast is the Lynx M20 Pro?
Deep Robotics lists a lab-tested maximum of 5 m/s and a recommended operating speed of 2 m/s. Plan routes around the 2 m/s figure.
Can it climb stairs?
Yes. The listing rates it for continuous stairs up to 25 cm, single steps up to 80 cm, and slopes up to 45 degrees, using Model Predictive Control and Reinforcement Learning to switch between rolling and walking.
Is the Lynx M20 Pro weatherproof?
It is IP66-rated against dust and water and operates from -20 to 55 degrees Celsius, with bidirectional lighting for work in darkness.
What is included with the robot?
The Lynx M20 Pro unit, a hot-swappable battery pack (quantity per configuration), a battery charger and power cable, a remote controller for manual operation (per configuration), and the user manual and quick-start guide.
What warranty does RoboticsSelect provide on the Lynx M20 Pro?
A 12-month full-unit warranty from the date of delivery, with the battery and joints covered for 6 months. RoboticsSelect is an authorized Deep Robotics dealer, so warranty support is handled through our support team.