Skip to main content Skip to content

Robotic Pool Cleaners

How WYBOT Pool Cleaners Work Efficiently

7 min read
WYBOT A1 cordless robotic pool cleaner on the floor of a pool

WYBOT builds cordless robotic pool cleaners that pull water through an onboard filter while they drive the floor, climb the walls, and scrub the waterline, and RoboticsSelect carries the line from the floor-only A1 to the self-charging S2 Solar Vision. This article explains how the cleaners work, which parts of the design do the work (motors, filtration, navigation, and charging), and how to match a model to your pool so the cleaner finishes on one charge.

Key takeaways

  • Suction scales with the motor system: 2,280 GPH on the dual-motor A1, 3,592 GPH on the brushless triple-motor C2 and S2, and 3,883 GPH on the C2 Vision.
  • Pool ratings run from 1,076 square feet (A1) to 2,152 (C2) to 3,230 (S2); runtime from 120 minutes (A1) to 210 minutes (S2).
  • Every model uses a 180 micron primary filter; the C2 and C2 Vision add a 10 micron ultra-fine layer.
  • The A1 cleans the floor only; every other model adds walls and the waterline, and the F1 skimmer handles the surface.
  • The S2 Solar and S2 Solar Vision return to an underwater solar dock when the battery drops below 20 percent.

How does a WYBOT pool cleaner work?

Every WYBOT cleaner follows the same cycle. You charge the unit, pick a mode on the unit or in the WYBOT app, lower it into the water, and let it run. Motors pull water through the filter and drive the cleaner along its path, debris stays in the filter, and when the cycle ends or the battery runs low the robot parks itself at the wall or pool edge so you can lift it out, rinse the filter, and recharge it. Efficiency comes from four design choices that differ by model: how much water the motors move, how fine the filtration is, how the cleaner decides where to go, and how it recharges.

Motors and suction: how debris gets lifted

WYBOT rates suction in gallons per hour, and the figure tracks the motor system. The entry WYBOT A1 uses a dual-motor system rated at 2,280 GPH, with wheels propelled by water flow rather than a drive motor. The C1 moves to a triple-motor system at 3,038 GPH, which drives wall climbing. The WYBOT C2 and WYBOT S2 use brushless triple-motor systems at 3,592 GPH, and the C2 Vision is rated at 3,883 GPH.

Flow and runtime together set the pool rating. The S2 pairs 3,592 GPH with a 210-minute runtime for pools up to 3,230 square feet; the A1 pairs 2,280 GPH with 120 minutes for pools up to 1,076 square feet. Matching the rating to your pool is what keeps a cycle from ending before the pool is done.

Filtration: what the cleaner keeps

Every WYBOT cleaner starts with a 180 micron filter that catches leaves, sand, and dirt; the difference is the second layer. The A1 adds a textured foam layer to its 180 micron mesh. The C2 pairs a 180 micron filter box with a 10 micron ultra-fine filter in a 3-liter capacity, which the listing recommends for pools that collect sand, pollen, or dead algae; the C2 Vision uses a 10 micron ultra-fine HEPA filter. The S2 adds an ultra-fine cotton foam layer, and the S2 Solar models a 40 ppi ultra-fine sponge.

Finer filtration has a cost in attention: the C2 listing notes that the fine filter clogs faster in heavily soiled water and may need rinsing partway through a cycle, and it recommends Turbo mode with the 10 micron filter for the deepest clean. On every model, the filter comes out after the cycle and rinses under a hose.

WYBOT S2 cordless robotic pool cleaner, suction power comparison before and after cleaning
The S2's suction clears sand and fine debris from the floor; before-and-after panels from WYBOT's listing.

Navigation and modes: how the cleaner decides where to go

The A1 is the simplest: it drives the floor, and its edge-enhanced behavior pauses it for a few seconds at the wall to boost cleaning along the edge before it turns back. It offers four modes, a cycle timer for up to four cleanings a week, and a wheel alignment setting matched to the pool shape. It does not climb walls or clean the waterline, and WYBOT limits it to slopes under 15 degrees.

The C2 and S2 add wall climbing, waterline cleaning, and route choice. Through the WYBOT app, both offer seven modes (Full, Floor, Wall, Waterline only, Wall then Floor, Turbo, and Eco on the C2) and six cleaning paths, scheduling for up to four cleanings a week, and over-the-air updates; the S2 also has three modes on the unit for use without a phone. Mode affects runtime: the C2 runs up to 180 minutes in Eco but about 60 minutes in Turbo.

The Vision models add an onboard AI camera. The WYBOT C2 Vision uses it to detect debris and avoid obstacles, and its Dirt Hunting mode targets the areas of the floor with the most debris; WYBOT states the AI learns your pool's patterns over the first month. The S2 Solar Vision applies the same idea to the S2 Solar platform, with an AI Vision mode that WYBOT states cleans the floor up to 20 times faster.

Charging: standard chargers versus the solar dock

Most WYBOT cleaners charge on a standard power adapter after you lift them out: about 2.5 hours on the A1 and about 3 hours on the C2 and S2. The S2 Solar and S2 Solar Vision change the routine. They run over 2.5 hours per cycle and, when the battery drops below 20 percent, return on their own to an underwater solar-powered charging dock at the waterline of an in-ground pool, so they can run on a weekly schedule without handling; a DC charger is available as a backup.

The WYBOT F1 skimmer is solar-powered in a different way: a 33 watt panel keeps it floating and running through the day, in a Smart Mode that cycles 10 minutes on and 10 minutes off for 24 hours or a Standard Mode that runs 8 hours straight. It clears leaves, bugs, pollen, and twigs into a 7-liter basket before they sink, so the floor cleaner has less to handle.

Which WYBOT model fits your pool?

Flat-bottom pools up to 1,076 square feet: A1

The A1 suits above-ground and flat-bottom in-ground pools where the floor is the job. It is not suited to slopes over 15 degrees or significant liner wrinkles.

Small to mid-sized pools up to 2,152 square feet: C1, C2, or C2 Vision

The C1 (1,615 square feet, 150 minutes in Eco) covers the floor, walls, waterline, steps, and slopes with a single 180 micron filter. The C2 (2,152 square feet, 180 minutes in Eco) adds brushless motors, 3,592 GPH, and the 10 micron second filter. The C2 Vision adds the AI camera, 3,883 GPH, and an eighth mode.

Large pools up to 3,230 square feet: S2, S2 Solar, or S2 Solar Vision

The S2 is the long-runtime choice at 210 minutes, with on-unit modes for owners who skip the app. The S2 Solar and S2 Solar Vision suit in-ground pools where the owner wants the cleaner to recharge itself at the dock. The WYBOT comparison page puts every model side by side.

Before you buy

Check three things against your pool: surface area versus the model's rating, whether the floor is flat (the A1 needs a slope under 15 degrees), and whether you want walls and the waterline cleaned (every model except the A1 does both). A standard adapter means lifting the unit out after each cycle, while the S2 Solar dock needs an in-ground pool. Pick the mode and path on land before the unit goes in, and plan a full charge before the first run.

Warranty, shipping, and support

WYBOT's limited warranty covers defects in materials and workmanship under normal residential use from the date of delivery: 1 year on the A1 and B1, and 2 years on the C1, C2, C2 Vision, S2, S2 Solar, and S2 Solar Vision. Misuse, unauthorized repair, water chemistry outside the recommended range, and normal wear on filters, sponges, and brushes are excluded. RoboticsSelect is an authorized WYBOT dealer, so warranty support is handled through us and we coordinate with WYBOT.

Shipping is free to the contiguous 48 U.S. states; we do not ship to PO boxes, Alaska, Hawaii, Puerto Rico, or outside the U.S. Unopened, unused units can be returned within 30 days under the refund policy. Our U.S.-based product-trained team is at support@roboticsselect.com or (412) 415-7375.

The takeaway

A WYBOT cleaner works efficiently when its motor, filter, navigation, and charging system match the pool: 2,280 GPH for a flat floor, brushless motors and a 10 micron filter for a mid-sized pool with fine debris, 210 minutes of runtime for a large pool, and a solar dock when you want the cleaner to look after itself. Start from your pool's size and surfaces and the right model follows; every one is in the WYBOT collection at RoboticsSelect.

Products in this article

FAQ

Do WYBOT pool cleaners need a cord or hose?

They do not. Every WYBOT cleaner at RoboticsSelect runs on a built-in battery, charges on a power adapter or, on the S2 Solar models, at an underwater solar dock, and parks itself at the pool edge when the cycle ends.

Which WYBOT models climb walls and clean the waterline?

The C1, C2, C2 Vision, S2, S2 Solar, and S2 Solar Vision all clean the floor, walls, and waterline. The A1 cleans the pool floor only and is built for flat-bottom pools with a slope under 15 degrees.

How long does a WYBOT cleaner run per charge?

The A1 runs up to 120 minutes, the C1 up to 150 minutes in Eco mode, the C2 and C2 Vision up to 180 minutes in Eco mode (about 60 minutes in Turbo on the C2), and the S2 up to 210 minutes. The S2 Solar models run over 2.5 hours per cycle and recharge at their dock.

What is the difference between the C2 and the C2 Vision?

The C2 Vision adds an onboard AI camera that detects debris and avoids obstacles, a Dirt Hunting mode that targets the dirtiest areas, an eighth cleaning mode, and 3,883 GPH of suction versus 3,592 GPH on the C2. Both are rated for pools up to 2,152 square feet.

How does the WYBOT S2 Solar recharge itself?

When its battery drops below 20 percent, the S2 Solar returns to an underwater solar-powered charging dock mounted at the waterline of an in-ground pool. A DC charger is also included, so you can charge by cable when needed.

What warranty do WYBOT cleaners carry?

WYBOT covers the A1 for 1 year and the C1, C2, C2 Vision, S2, S2 Solar, and S2 Solar Vision for 2 years against defects under normal residential use. RoboticsSelect is an authorized WYBOT dealer and handles warranty support; filters, sponges, and brushes are wear parts and are not covered.