Skip to main content Skip to content

Robotic Pool Cleaners

WYBOT A1 Cordless Robotic Pool Cleaner Guide

5 min read
WYBOT A1 cordless robotic pool cleaner in a backyard pool with a family on the deck

The WYBOT A1 is a cordless robotic pool cleaner for the floor of above-ground and flat-bottom in-ground pools up to about 1,076 square feet. This guide covers what the A1 cleans and what it leaves alone, how to check whether your pool fits it, how to set it up, and when a different WYBOT model is the better buy.

Key takeaways

  • The A1 cleans the pool floor only, in pools up to about 1,076 square feet with a slope under 15 degrees and water up to 8.2 feet deep.
  • A dual-motor system drives 2,280 GPH of suction, and a dual-layer filter pairs a 180 micron mesh with a textured foam layer.
  • It runs up to 120 minutes per charge, recharges in about 2.5 hours, and its cycle timer handles up to four cleanings a week.
  • WYBOT covers the A1 with a 1-year limited warranty from the date of delivery.

What does the WYBOT A1 clean, and what does it leave alone?

The A1 is a floor cleaner. It collects leaves, sand, dirt, and fine debris from flat pool floors in tile, vinyl, concrete, and fiberglass, and it does not climb walls or clean the waterline. That single job is the reason to choose it: if vacuuming the bottom is the chore you want gone, the A1 is built for exactly that.

Edges get extra attention. When the A1 reaches a wall it pauses for a few seconds to boost cleaning there, then returns to the floor, which targets the strip along the wall that many robots miss. Its wheels are propelled by water rather than a separate drive motor, and WYBOT describes it as one of its simplest models to run: lower it in and it starts cleaning.

Specification WYBOT A1
Cleaning coverage Pool floor only
Pool type Above-ground and flat-bottom in-ground
Ideal pool size Up to 1,076 sq ft
Maximum slope Less than 15 degrees
Maximum water depth 8.2 ft
Suction 2,280 GPH, dual-motor system
Filtration 180 micron mesh plus a textured foam layer
Runtime and charging Up to 120 minutes; about 2.5 hours to charge
Control 4 cleaning modes, cycle timer for up to 4 cleanings per week, 5-color LED, WYBOT app compatible
Warranty 1-year limited

Does your pool fit the A1?

Fit comes down to the floor. The A1 is designed for flat bottoms, and the listing says it is not suited to pools with a slope over 15 degrees or with significant liner wrinkles, where it can struggle to move. Check the deepest point as well, since the rated maximum water depth is 8.2 feet.

Size is the next check. The listing rates the A1 for pools up to about 1,076 square feet; for a rectangular pool, length times width gives the figure to compare. A 16 by 32 foot pool works out to 512 square feet, well inside the rating, while a 20 by 40 foot pool, at 800 square feet, still fits.

As for debris, the listing calls the A1 a strong fit for pools that collect sand and fine dust. The 180 micron mesh captures leaves and sand, and the textured foam layer adds fine-debris capture on top of it.

Lifting the lightweight WYBOT A1 out of a pool
After a cycle, the A1 is lifted out by hand and its filter rinsed.

How do you set up and run the A1?

Setup follows five steps from the listing. Keep the user manual handy, because the wheel alignment setting depends on your pool's shape.

  1. Charge it fully. A full charge takes about 2.5 hours; the charging port, power button, and LED sit on top of the unit.
  2. Set the wheel alignment. Match the alignment to your pool's shape as the manual describes, for example the rectangle setting for a rectangular pool.
  3. Pick a mode or set the timer. Choose one of the four cleaning modes, or set the cycle timer for up to four cleanings a week.
  4. Lower it in. Place the A1 in the pool and it begins cleaning automatically.
  5. Retrieve and rinse. When it parks near the wall, lift it out, remove and rinse the dual-layer filter, and store the unit out of direct sunlight.

The A1 works without a phone for basic operation, which suits owners who would rather not pair another device, and it is also compatible with the WYBOT app. A 5-color LED status indicator shows what the cleaner is doing at a glance.

In heavily soiled pools, the listing advises rinsing the foam layer often. Because the A1 parks at the wall when its battery runs low as well as when it finishes, retrieval stays the same whichever way a cycle ends.

When is a different WYBOT model the better choice?

If brushing walls or scrubbing the waterline is part of the chore you want gone, the A1 is the wrong tool. The WYBOT B1 keeps a compact body but cleans floors, walls, waterline, steps, and slopes in pools up to about 1,150 square feet. For larger pools, the A1 listing names the C1, C2, and C2 Vision as the better fit for wall and waterline cleaning; the WYBOT comparison page lines them up.

If floating leaves are the bigger nuisance, the problem sits at the surface rather than the floor. The A1 & F1 bundle pairs the A1 with the F1 solar skimmer, which clears leaves, bugs, and pollen before they sink. Because the A1 stays on the floor in that pairing too, walls and the waterline remain a manual job.

WYBOT A1 dual-layer filtration
The dual-layer filter pairs a 180-micron mesh with a foam layer.

Before you buy

Measure the pool and look closely at the floor before ordering. A slope over 15 degrees, significant liner wrinkles, or water deeper than 8.2 feet each rule the A1 out. If the floor fits and floor debris is the main chore, the A1 is a direct match; if you also want the walls cleaned, compare the B1 first.

Warranty, shipping, and support

WYBOT's 1-year limited warranty on the A1 covers defects in materials and workmanship in normal home use, starting from the date of delivery. It excludes normal wear on consumable parts such as filters and brushes, along with misuse, unauthorized repair or modification, and damage from water chemistry outside the recommended range. Replacement A1 filter sets and cotton foam are listed in the pool cleaner accessories collection.

As an authorized WYBOT dealer, RoboticsSelect handles A1 warranty support directly and works with WYBOT on any claim, so keep your order number or proof of purchase. Delivery is free to addresses in the contiguous 48 states, excluding PO boxes, Alaska, Hawaii, Puerto Rico, and international addresses. Unopened, unused units fall under the 30-day return window in the refund policy. For fit or setup questions, call our U.S.-based, product-trained team at (412) 415-7375 or email support@roboticsselect.com.

The takeaway

The A1 is a sound buy for one specific job: keeping the floor of a flat-bottom pool clean without a cord in the water. Confirm the slope, depth, and size against its ratings, decide whether walls matter to you, and see the full specifications and package contents on the WYBOT A1 product page.

Products in this article

FAQ

Will the A1 clean pool walls or the waterline?

It cleans the floor only; at each wall it pauses briefly to boost cleaning along the edge, then returns to the floor. For walls and the waterline, the listing points to the C1, C2, and C2 Vision, and the B1 covers both in smaller pools.

Can the A1 handle a pool with a sloped deep end?

It is designed for flat bottoms with a slope under 15 degrees, and the listing says it is not suited to steeper slopes or significant liner wrinkles. Its maximum rated water depth is 8.2 feet.

Does the A1 need a phone or the app to run?

The A1 works without a phone for basic operation, using its four cleaning modes and a cycle timer that schedules up to four runs a week. It is also compatible with the WYBOT app.

How long does the A1 run on a charge?

Up to 120 minutes per charge, with a recharge of about 2.5 hours. When the battery runs low, it parks near the wall for retrieval.

What warranty covers the WYBOT A1?

A 1-year limited warranty against defects in materials and workmanship from the date of delivery, handled through RoboticsSelect as an authorized WYBOT dealer. Normal wear on filters and brushes is not covered.