Skip to main content Skip to content

Robotic Pool Cleaners

How to Maintain Your WYBOT S2

6 min read
WYBOT S2 cordless robotic pool cleaner covering the floor, walls, and waterline of a pool

The WYBOT S2 is WYBOT's high-end cordless cleaner for large pools, and keeping it working well takes a short routine rather than a service schedule. This guide covers that routine step by step, from rinsing the filter and foam to charging and sealing the port, based on the S2 listing at RoboticsSelect, and explains what the 2-year warranty does and does not cover.

Key takeaways

  • The S2 is rated for pools up to 3,230 square feet, runs up to 210 minutes per charge, and recharges in about three hours.
  • After each cycle, lift it out where it parks at the pool edge and rinse both filtration layers under a hose: the 180 micron filter and the ultra-fine cotton foam.
  • Refit the foam with its cut side oriented correctly so the lid closes, and twist the charging port cover tight before the S2 goes back in the water.
  • WYBOT's 2-year limited warranty covers defects; filters, sponges, and brushes are wear parts it does not cover.

What does the S2 need from you after every cycle?

The S2 ends each cycle by parking itself at the pool edge, and it does the same when its battery runs low. That is your cue: lift the cleaner out, open it, and rinse the 180 micron filter and the ultra-fine cotton foam under a hose before you set it aside.

The two layers do different jobs. The 180 micron filter holds the larger debris, such as leaves and dirt, while the cotton foam traps the fine particles that would slip through a coarser screen. Rinse both every time rather than waiting until one looks full, so the next cycle starts with clean filtration.

  1. Retrieve: lift the S2 out once it parks at the pool edge.
  2. Rinse: remove the filter and the foam and rinse both under a hose.
  3. Refit the foam: seat it with the cut side oriented correctly so the lid closes fully.
  4. Seal the port: after any charge, twist the charging port cover tight.
  5. Charge or store: recharge if another cycle is due; otherwise store the unit as the S2 manual directs.

How do you rinse and refit the filter and foam?

Work the debris out of both pieces with the hose rather than just wetting the surface, paying particular attention to the foam, which is the layer that holds the finest particles. Let excess water drain before you reassemble the cleaner.

Refitting is the step that catches people out. The S2 listing calls out the foam's orientation specifically: put it back with the cut side positioned correctly so the lid closes. If the lid resists, take the foam out and turn it rather than pressing the cover down.

Plan on replacing the filtration parts over the life of the cleaner. WYBOT treats normal wear on filters, sponges, and brushes as outside the warranty, and RoboticsSelect lists a replacement filters box that fits the S2, along with an S2 cap, in the pool cleaner accessories collection.

WYBOT S2 dual-layer filtration
The dual-layer filter, a 180-micron filter plus a fine foam layer, is the part to rinse after each cycle.

Charging the S2 the right way

The S2 uses a standard charger, so it comes out of the pool to recharge between cycles. WYBOT asks for a full charge before the first run, and a full charge takes about three hours.

The listing is specific about one detail: twist the charging port cover tightly before the unit goes back in the water. Make that the last check every time the S2 leaves the charger, because a cover that is only partly closed is easy to miss when the cleaner is in your hands and on its way to the pool.

Charging also has to fit your schedule. The cycle timer can run up to four cleanings a week, so plan the charge between them and the S2 starts every scheduled cycle on a full battery.

Using the modes so maintenance stays simple

Choosing the right mode keeps the S2 from doing work twice. The WYBOT app, connected over Wi-Fi, offers seven cleaning modes and six cleaning paths, and three modes can be selected directly on the unit without a phone. The on-unit modes are handy when your phone is indoors or the app is not set up yet.

The S2 cleans floors, walls including tile, steps, and waterlines in above-ground and in-ground pools of all shapes, on tile, concrete, vinyl, and fiberglass. When a cycle leaves an area untouched, note which mode and path were running before you change anything, so you can compare the next cycle like for like.

Where the S2 fits in the S2 family

RoboticsSelect carries the standard WYBOT S2 on its own and in the S2 & F1 bundle, which adds WYBOT's F1 solar skimmer to catch floating leaves, bugs, and pollen before they sink to the S2's level. For owners who would rather not lift the cleaner out to charge it, the S2 Solar Vision returns to an underwater solar charging dock when its battery drops below 20 percent. It is designed for in-ground pools and adds an AI camera for floor cleaning.

The filter routine carries over between them. The S2 Solar Vision still needs lifting out periodically so its 180 micron filter box and 40 ppi ultra-fine sponge can be emptied and rinsed.

WYBOT S2 cleaning mode selection
Seven cleaning modes and six paths are chosen in the WYBOT app.

When to look closer, and when to call support

When pickup drops, start with the parts you maintain: rinse the filter and foam again and confirm the foam is seated so the lid closes properly. Check that the battery was fully charged before the cycle, and that the mode you chose covers the surfaces you expected.

If the S2 still underperforms or will not charge, stop there and contact support instead of opening the unit. The warranty excludes damage from unauthorized repair, disassembly, or modification, and from operation outside the official manual and stated operating range. It also excludes damage from running the S2 in water chemistry outside the recommended range, so keep the pool balanced to the range in the manual.

Before you buy

The S2 comes out of the pool to recharge and to have its filter and foam rinsed after each cycle, so plan for hose access near where it parks and a dry spot for the charger. Confirm your pool is within the 3,230 square foot rating. If lifting the cleaner out to charge is the step you want to avoid, compare the S2 Solar Vision, which returns to an underwater solar charging dock in in-ground pools. Once it is running, check two things before every launch: the foam's cut side is oriented so the lid closes, and the charging port cover is twisted tight.

Warranty, shipping, and support

The S2 carries WYBOT's 2-year limited warranty against defects in materials and workmanship under normal residential use, counted from the date of delivery. Normal wear on filters, sponges, and brushes falls outside it, and warranty service requires a valid proof of purchase or order number.

Because RoboticsSelect is an authorized WYBOT dealer, warranty and repair requests come to our U.S.-based, product-trained support team, which coordinates them with WYBOT; reach us at support@roboticsselect.com or (412) 415-7375. Shipping costs nothing within the contiguous 48 states, though we cannot deliver to PO boxes, Alaska, Hawaii, Puerto Rico, or outside the U.S.; see the shipping policy. A unit that is still unopened and unused can be returned within 30 days under the refund policy.

The takeaway

The S2 asks for little: a rinse of both filtration layers after each cycle, a correctly seated foam, a tight port cover, and a full charge before the next run. Keep those habits, replace wear parts as they wear, and send anything more serious to support; the WYBOT S2 product page lists the full specifications and what comes in the box.

Products in this article

FAQ

How often should the S2 filter and foam be rinsed?

After every cycle. When the S2 parks at the pool edge, lift it out and rinse both the 180 micron filter and the ultra-fine cotton foam under a hose.

Why will the S2 lid not close after cleaning the filter?

Check the foam. The S2 listing says to replace it with the cut side oriented correctly so the lid closes, so turn the foam rather than forcing the cover.

Can the S2 run without the WYBOT app?

Yes. Three cleaning modes can be selected directly on the unit, while the app over Wi-Fi adds seven modes, six paths, and a cycle timer for up to four cleanings a week.

What should be checked before the S2 goes back in the pool after charging?

Twist the charging port cover tightly before placing the unit in the water. A full charge takes about three hours, and the S2 should be fully charged before its first run.

Are the S2 filter and foam covered by the warranty?

The 2-year limited warranty covers defects in materials and workmanship, but normal wear on filters, sponges, and brushes is excluded. A replacement filters box that fits the S2 is listed in the pool cleaner accessories collection.