Roborock Q7 Max Robot Vacuum and Mop with 4200 Pa Power Suction

It vacuums hardwood, tile, laminate, and low-pile carpet or rugs, and the all-rubber main brush resists hair wrap so pet hair goes into the 470 ml bin. With Carpet Boost on, suction jumps to maximum when the brush senses the extra resistance of carpet and drops back on hard floors. The cliff sensors can read very dark or shag carpet as a drop, so the robot may avoid those rugs or report Error 4; that behavior cannot be switched off.

No. Roborock's automatic mop lifting is limited to the S7, S8, and Qrevo families, so the Q7 Max drags its mop cloth wherever it drives. Take off the mop cloth mount before a carpet run, or draw No-Mop Zones and No-Go Zones in the app so mopping passes skip rugs; the robot does not recognize magnetic boundary strips, so app zones are the only boundaries it honors.

The 350 ml electric water tank and the 470 ml dustbin are one combined unit that slides into the back of the robot, so you empty and refill in a single step. Attach the mop cloth to its mount, slide the mount under the robot until it clicks, then pick one of 30 water flow levels in the app; the mop presses at a constant 300 g and a full tank covers up to 2,583 sq ft. Roborock suggests vacuuming new floors at least three times before the first mopping pass so the cloth does not load up with grit.

Use clean, cold water; hot water can deform the tank. Roborock says to add only its own branded floor cleaner, diluted at 1:300, because foam from other cleaners can block the filter and corrode parts. Do not add disinfectant or essential oils.

The Q7 Max connects to 2.4 GHz Wi-Fi only; 5 GHz is not supported, so choose the 2.4 GHz network on a dual-band router. When the Roborock app asks you to scan a QR code, look under the top cover or dustbin or on top of the machine; if you cannot find it, tap Search for Device and then No QR code found to continue pairing. If the connection still fails, re-enter the password, allow location and local network permissions for the app, switch off any VPN, and avoid WEP security or special characters in the network name.

PreciSense LiDAR stores up to 4 level maps with 3D map views, each with its own No-Go Zones and Invisible Walls, and Routines let you start a room, zone, or whole-home clean with one tap or on a schedule. For another floor, switch the map setting to multi-floor, tap create new map, and carry only the robot (not the dock) upstairs. Amazon Alexa, Google Home, and Apple Siri Shortcuts are supported once the robot is linked in the Roborock app; for Alexa, say "Alexa, open robo rock" and then the command, such as "clean the living room".

The 5200 mAh battery runs up to 3 hours and vacuums up to 3,229 sq ft in Quiet mode, recharging and resuming on larger floors. A full charge takes under 6 hours; cleaning will not resume after a recharge if Do Not Disturb is active or if you placed the robot on the dock by hand, and scheduled cleans only start above 20 percent battery. Roborock recommends leaving the robot on the dock whenever it is used at least weekly: once the battery is full only the main board draws power, so it does not shorten battery life. Off the dock the robot powers itself down after 24 hours of inactivity and has to be switched on by hand; if it will sit unused for several months, power it off.

Clean the main brush every 2 weeks and replace it every 6 to 12 months; clean the side brush monthly and replace it every 3 to 6 months; rinse the dustbin and water tank combo weekly and replace the E11 washable filter every 6 to 12 months. Wash the mop cloth after every use and replace it every 3 to 6 months, and wipe the sensors, main wheels, and charging contacts monthly. Operate only between 39 and 104 F (4 to 40 C).

Put the dock on a hard, level floor against a wall with at least 1.6 ft (0.5 m) of clearance on each side and more than 4.9 ft (1.5 m) in front of the charging dock, keep that area clear, and wipe the signal window on the front of the dock and the robot's front sensor; a robot that was carried elsewhere or just finished a spot clean rebuilds its map and may need to be placed on the dock by hand. Error 13 means dirty charging contacts: wipe them with a cloth dampened with rubbing alcohol, unplug the dock for two minutes, and try another outlet. Error 1 is a blocked LiDAR turret, Error 4 a dirty cliff sensor or dark carpet, Error 5 a jammed main brush, Error 7 jammed wheels, and Error 8 a trapped robot; clear the part named and restart. Error 10 or a filter blocked or wet alert means wash and fully dry the filter, Error 18 means tap the side of the robot to shake debris out of the fan, and an internal error calls for a factory reset before contacting Roborock support.

Roborock covers new products such as the Q7 Max with a one-year limited warranty from the purchase date against defects in materials and workmanship. Consumables such as filters, brushes, mop cloths, and dust bags are not covered unless a defect in a non-consumable part damaged them, and normal wear, cosmetic damage, misuse, and commercial use are excluded. Keep your receipt: without proof of purchase the warranty period defaults to three months from the factory ship date. Warranty and technical support run through Roborock US at support@roborock.com or 1-855-960-4321 (24/7); RoboticsSelect is an authorized dealer, ships free within the contiguous U.S., and accepts standard returns within 30 days.