Roborock Q7 Max+ Robot Vacuum with Auto-Empty Dock Pure

After each cleanup the dock vacuums the robot's 470 ml bin into a sealed 2.5 L dust bag while filtering 99.7 percent of pollen as small as 0.3 microns. The bag holds up to 7 weeks of debris and Roborock suggests replacing it about every 7 weeks depending on use; if emptying weakens, check that the main brush and brush cover are seated, that the air duct is clear, and that the bag handle is pushed all the way down. The dock is a US 100 to 120 V unit and plugs into a standard outlet.

Auto-emptying only runs when the robot docks itself after cleaning: it will not start if you set the robot on the dock by hand, if the robot returned without cleaning, or during the Do Not Disturb period, which is 22:00 to 08:00 by default. Make sure auto-emptying is enabled in the app and the dustbin cover is installed. A steady red light on the dock usually means the dustbin cover or bag is not seated or the fan paused after overheating; unplug the dock for 30 minutes and try again.

It vacuums hardwood, tile, laminate, and low-pile carpet or rugs; the all-rubber main brush sheds hair instead of wrapping it, and with Carpet Boost on, suction rises to maximum when the brush senses carpet resistance. It does not lift its mop: automatic mop lifting is limited to Roborock's S7, S8, and Qrevo families, so remove the mop cloth mount before a carpet run or draw No-Go Zones and Invisible Walls around rugs in the app, since the robot does not recognize magnetic boundary strips. The cliff sensors can read very dark or shag carpet as a drop, so the robot may avoid those rugs or report Error 4; Roborock does not allow the sensors to be disabled.

The 350 ml electric water tank is combined with the 470 ml dustbin in one slide-in unit, so filling and emptying happen together. Clip the mop cloth onto its mount, slide the mount under the robot until it clicks, and choose one of 30 water flow levels in the app; the mop presses with a constant 300 g and a full tank covers up to 2,583 sq ft at low flow. Use clean, cold water: hot water can deform the tank, and Roborock allows only its own floor cleaner, diluted 1:300, because other cleaners can foam and block the filter.

The Q7 Max+ connects to 2.4 GHz Wi-Fi only; 5 GHz is not supported, so choose the 2.4 GHz network on a dual-band router. When the Roborock app asks you to scan a QR code, look under the top cover or dustbin or on top of the machine; if you cannot find it, tap Search for Device and then No QR code found to continue pairing. If the connection still fails, re-enter the password, allow location and local network permissions for the app, switch off any VPN, and avoid WEP security or special characters in the network name.

It stores up to 4 level maps with 3D views and recognizes which floor it is on automatically; each map keeps its own No-Go Zones and Invisible Walls, and Routines let you start a room, zone, or whole-home clean with one tap or on a schedule. Amazon Alexa, Google Home, and Apple Siri Shortcuts are supported; for Alexa, say "Alexa, open robo rock" and then the command.

The 5200 mAh battery runs up to 3 hours and vacuums up to 3,229 sq ft in Quiet mode, recharging and resuming on larger floors. A full charge takes under 6 hours; cleaning will not resume after a recharge if Do Not Disturb is active or if you placed the robot on the dock by hand, and scheduled cleans only start above 20 percent battery. Roborock recommends leaving the robot on the dock whenever it is used at least weekly: once the battery is full only the main board draws power, so it does not shorten battery life. Off the dock the robot powers itself down after 24 hours of inactivity and has to be switched on by hand; if it will sit unused for several months, power it off.

Clean the main brush every 2 weeks and replace it every 6 to 12 months; clean the side brush monthly and replace it every 3 to 6 months; rinse the dustbin and water tank combo weekly and replace the E11 washable filter every 6 to 12 months. Wash the mop cloth after each use and replace it every 3 to 6 months, wipe the sensors and charging contacts monthly, and change the dust bag when full. Operate only between 39 and 104 F (4 to 40 C).

Put the dock on a hard, level floor against a wall with clear floor in front of the dock and on both sides so the robot can line up straight, keep that area clear, and wipe the signal window on the front of the dock and the robot's front sensor; a robot that was carried elsewhere or just finished a spot clean rebuilds its map and may need to be placed on the dock by hand. Error 13 means dirty charging contacts: wipe them with a cloth dampened with rubbing alcohol, unplug the dock for two minutes, and try another outlet. Error 1 is a blocked LiDAR turret, Error 4 a dirty cliff sensor or dark carpet, Error 5 a jammed main brush, Error 7 jammed wheels, and Error 8 a trapped robot; clear the part named and restart. Error 10 or a filter blocked or wet alert means wash and fully dry the filter, Error 18 means tap the side of the robot to shake debris out of the fan, and an internal error calls for a factory reset before contacting Roborock support.

Roborock covers new products such as the Q7 Max+ with a one-year limited warranty from the purchase date against defects in materials and workmanship. Consumables such as filters, brushes, mop cloths, and dust bags are not covered unless a defect in a non-consumable part damaged them, and normal wear, cosmetic damage, misuse, and commercial use are excluded. Keep your receipt: without proof of purchase the warranty period defaults to three months from the factory ship date. Warranty and technical support run through Roborock US at support@roborock.com or 1-855-960-4321 (24/7); RoboticsSelect is an authorized dealer, ships free within the contiguous U.S., and accepts standard returns within 30 days.