Robotic Pool Cleaners
WYBOT C2 Cordless Robotic Pool Cleaner Guide
The WYBOT C2 is a cordless robotic pool cleaner for mid-sized pools, and most of what keeps it working well happens on the pool deck: choosing the right mode before it goes in, rinsing two filters when it comes out, and charging it the right way. This guide covers first-run setup, the seven cleaning modes, the ultra-fine filter, the after-run routine, and the first checks to make when results slip, based on the C2 listing at RoboticsSelect.
Key takeaways
- The C2 is rated for above-ground and in-ground pools up to 2,152 sq ft and cleans the floor, walls, waterline, steps, and slopes with 3,592 GPH from a brushless triple-motor system.
- It runs up to 180 minutes in Eco mode and about 60 minutes in Turbo, and recharges in about three hours.
- Choose one of seven modes and six paths in the WYBOT app while the C2 is out of the water; scheduling covers up to four cleanings a week.
- After each run, lift it out where it parks at the pool edge and rinse both the 180 micron filter box and the 10 micron ultra-fine filter.
- WYBOT's 2-year limited warranty covers defects; filters and brushes are wear parts, and genuine replacements are listed at RoboticsSelect.
What does the WYBOT C2 do?
The WYBOT C2 sits above the entry-level WYBOT C1 in WYBOT's cordless range. Per the listing, it builds on the C1 with a brushless motor, higher suction, and dual-layer filtration, and it works on tile, concrete, vinyl, and fiberglass in pools of any shape. When the cycle ends or the battery runs low, it returns to the pool edge so you can lift it out.
| Specification | WYBOT C2 |
|---|---|
| Ideal pool size | Up to 2,152 sq ft |
| Pool type | Above-ground and in-ground, all pool shapes |
| Cleaning coverage | Floor, walls, waterline, steps, and slopes |
| Suction | 3,592 GPH |
| Motor and brushes | Brushless triple-motor system; dual brushes |
| Filtration | 180 micron filter box plus 10 micron ultra-fine filter, 3 L capacity |
| Runtime | Up to 180 minutes in Eco; about 60 minutes in Turbo |
| Charging | About 3 hours |
| Modes and paths | 7 cleaning modes, 6 cleaning paths |
| Scheduling | Up to 4 cleanings per week; over-the-air updates |
| App | WYBOT app over Wi-Fi |
| Warranty | 2-year limited |
How do you set up the C2 for its first run?
The listing lays out five steps, and they double as the routine for every run after the first:
- Charge it fully: a full charge takes about three hours. Make sure the unit is off and the charging port is dry before you connect the charger.
- Install the app: download the WYBOT app, create or sign in to an account, and connect over Wi-Fi.
- Pick a mode on land: choose the cleaning mode and path in the app while the C2 is out of the water.
- Place and run: lower the C2 into the pool and start the cycle.
- Retrieve and clean: when it parks at the edge, lift it out, remove and rinse both filters, and store it out of direct sunlight.
The box contains the C2, a charger for a standard outlet, the 180 micron filter box and 10 micron ultra-fine filter, and a user manual with a quick-start guide. Keep the manual with the charger; it is the reference for anything beyond the routine in this guide.
Treat the first run as a baseline. Note the mode and path you chose, where the C2 cleaned well, and what came out in the filters. That record makes later adjustments easier to judge than memory does.
Which cleaning mode should you choose?
The C2 offers seven modes and six cleaning paths in the WYBOT app. Match the mode to the job in front of you rather than running the same program every time:
| Mode | When to use it |
|---|---|
| Full | A general run over the whole pool |
| Floor | Debris has settled on the bottom |
| Wall | The walls need attention between full runs |
| Waterline only | Grime has built up where the water meets the wall |
| Wall then Floor | Walls first, then the bottom, in one cycle |
| Turbo | A stronger, shorter run of about 60 minutes; the listing pairs it with the ultra-fine filter for fine debris |
| Eco | The longest run, up to 180 minutes |
Change one setting at a time and write down the mode and path you ran, so a missed area can be traced to a setting instead of guessed at. Scheduling allows up to four cleanings a week; start with fewer and add runs if the pool needs them.

How do you use the two filters?
The C2 filters in two layers. The 180 micron filter box catches leaves and sand, and the 10 micron ultra-fine filter traps fine dirt and algae, with 3 liters of capacity between them. Per the listing, the fine filter suits pools that collect sand, pollen, or dead algae, and it pairs with Turbo mode for the deepest clean.
The trade-off is clogging. The listing notes that the fine filter clogs faster in heavily soiled water and may need rinsing partway through a cycle. When the pool is full of leaves or heavy debris, clear the bulk first with a regular run and a freshly emptied filter box, then follow with a fine-filter Turbo run once the water is cleaner.

What should you do after every run?
The C2 parks at the pool edge when the cycle ends or the battery runs low. That is the cue for a short routine:
- Retrieve: lift the C2 out once it parks at the edge.
- Rinse both filters: remove the filter box and the ultra-fine filter and rinse them under a hose until the mesh runs clear.
- Check the brushes: clear any hair, leaves, or string caught around the dual brushes.
- Reassemble: refit both filters and close the lid fully.
- Charge or store: if another run is due, charge it with the unit off and the port dry; otherwise store it out of direct sunlight.
Rinse after every run rather than waiting until the filters look full. The C2 filters set listing explains why: fine debris packs the mesh, and suction drops as the filter clogs, which shows up as weaker pickup on the next run.
Charging and replacement parts
Charge with the C2 switched off and the charging port dry, using the charger made for it. The replacement charger listing notes that chargers for other WYBOT models are not interchangeable; the genuine WYBOT C1, C2 and C2V charger works as a spare or a replacement.
Filters and brushes wear with use and fall outside the warranty, so plan on replacing them over the life of the cleaner. The WYBOT C2 and C2V filters set includes a 180 micron filter box and the ultra-fine secondary filter, and the WYBOT C2 filter cotton is sold on its own. Replace a filter when it is torn, permanently stained, or no longer rinses clean.
What should you check when cleaning results drop?
Start with the parts you maintain before assuming a fault:
| What you notice | Check first |
|---|---|
| Weaker debris pickup | Both filters rinsed; the ultra-fine filter not clogged partway through a run in dirty water |
| The run ends sooner than expected | A full charge before the run; Turbo runs about 60 minutes against up to 180 in Eco |
| Walls or waterline skipped | Whether the selected mode includes walls or the waterline |
| The same floor area missed twice | The selected cleaning path, then a different path on the next run |
| Settings not taking effect | The mode was set in the app before the C2 went in, and the software is current through over-the-air updates |
If the C2 still underperforms or will not charge after those checks, contact our support team with the mode, path, and what you saw. Do not open the unit: the warranty excludes damage from unauthorized repair, disassembly, or modification.
Keep water care separate from debris cleanup
The C2 removes debris; it does not balance the water. Keep your pool's normal filtration, testing, and chemical routine running alongside it. The warranty also excludes damage from running the unit in water chemistry outside the recommended range, so keep the pool within the range given in the C2 manual.
C1, C2, or C2 Vision?
The C2 shares its pool size rating and Eco runtime with the C2 Vision and steps up from the C1 in suction, filtration, and modes:
| Specification | WYBOT C1 | WYBOT C2 | WYBOT C2 Vision |
|---|---|---|---|
| Ideal pool size | Up to 1,615 sq ft | Up to 2,152 sq ft | Up to 2,152 sq ft |
| Suction | 3,038 GPH | 3,592 GPH | 3,883 GPH |
| Filtration | 180 micron cartridge | 180 micron plus 10 micron ultra-fine | 180 micron plus 10 micron ultra-fine HEPA |
| Cleaning modes | 5 | 7 | 8, including Vision (Dirt Hunting) |
| Eco runtime | Up to 150 minutes | Up to 180 minutes | Up to 180 minutes |
| AI camera | Not included | Not included | Onboard AI camera |
The C2 Vision adds an onboard AI camera whose Vision mode focuses on the dirtiest areas of the floor. For floating leaves, the C2 and F1 bundle pairs the C2 with WYBOT's solar F1 skimmer and its 7 L basket; our WYBOT bundles guide explains how the two robots split the work. For pools larger than 2,152 sq ft, the WYBOT comparison page lines the C2 up against the S2 and the rest of the range.
Before you buy
Measure the pool against the C2's 2,152 sq ft rating and confirm the surface is tile, concrete, vinyl, or fiberglass. The C2 comes out of the water to charge, so plan a charging spot out of direct sunlight, and make sure your home Wi-Fi reaches the place where you set it up in the app. If floating leaves are a daily chore, compare the C2 and F1 bundle; if you want camera-guided floor cleaning, compare the C2 Vision.
Warranty, shipping, and support
The C2 carries WYBOT's 2-year limited warranty against defects in materials and workmanship under normal residential use, counted from the date of delivery. It does not cover misuse, accident, or operation outside the official manual and stated operating range; unauthorized repair, disassembly, or modification; normal wear on consumable parts such as filters and brushes; or damage from water chemistry outside the recommended range. Warranty service requires a valid proof of purchase or order number.
RoboticsSelect is an authorized WYBOT dealer, so warranty and repair requests come to our U.S.-based, product-trained support team at support@roboticsselect.com or (412) 415-7375, and we coordinate them with WYBOT. Shipping is free to the contiguous 48 U.S. states; we do not ship to PO boxes, Alaska, Hawaii, Puerto Rico, or outside the U.S. (see the shipping policy). Unopened, unused units can be returned within 30 days under the refund policy.
The takeaway
The C2 rewards a short, steady routine: set the mode on land, rinse both filters after every run, save the ultra-fine filter and Turbo for fine debris once the heavy material is gone, and charge with the unit off and the port dry. Every WYBOT cleaner we carry, along with genuine filters and chargers, is in the WYBOT collection at RoboticsSelect.
Products in this article
FAQ
How often should the WYBOT C2 filters be rinsed?
After every run. When the C2 parks at the pool edge, lift it out and rinse both the 180 micron filter box and the 10 micron ultra-fine filter, because suction drops as the mesh clogs.
When should the 10 micron ultra-fine filter be used?
For fine debris such as sand, pollen, or dead algae, paired with Turbo mode for the deepest clean. It clogs faster in heavily soiled water and may need rinsing partway through a cycle, so clear heavy debris first.
How long does the WYBOT C2 run on a charge?
Up to 180 minutes in Eco mode and about 60 minutes in Turbo. A full charge takes about three hours; charge with the unit off and the charging port dry.
When should the cleaning mode be selected?
In the WYBOT app, while the C2 is out of the water. Choose from seven modes and six paths, then lower it into the pool and start the cycle; scheduling covers up to four cleanings a week.
What is the difference between the C2 and the C2 Vision?
Both are rated for pools up to 2,152 sq ft and run up to 180 minutes in Eco mode. The C2 Vision adds an onboard AI camera, a Vision (Dirt Hunting) mode, and 3,883 GPH against the C2's 3,592 GPH. The WYBOT comparison page lines them up.
Are the C2 filters and brushes covered by the warranty?
No. WYBOT's 2-year limited warranty covers defects in materials and workmanship, but normal wear on consumable parts such as filters and brushes is excluded. Genuine replacements, including the C2 and C2V filters set, are in our pool cleaner accessories collection.